介绍STDRIVE601主要特性,框图,典型应用框图以及三相栅极驱动器演示板EVALSTDRIVE601主要特性,电路图,材料清单和PCB设计图

STDRIVE601是单片三相半桥高压栅极驱动器,采用BCD6s离线技术制造,用于N沟功率MOSFET或IGBT,适用于三相应用.所有器件的源电流和沉电流分别是350mA和200mA.采用互锁和死区功能可防止交叉导通.器件的高压可高达600V,dV/dt瞬态度端正免疫度为±50 V/ns,栅极驱动电压范围从9V到20V,整个输入-输出传输时延为85ns,所有通路匹配传输入时延,带滞后的3.3V,5V TTL/CMOS输入,集成了阴极负载二极管(自举二极管),主要用在三相马达驱动和逆变器.本文介绍了STDRIVE601主要特性,框图,典型应用框图以及三相栅极驱动器演示板EVALSTDRIVE601主要特性,电路图,材料清单和PCB设计图.

The STDRIVE601 is a high voltage devicemanufactured with BCD6s offline technology. It isa single-chip with three half-bridge gate drivers forN-channel power MOSFETs or IGBTs suitable for3-phase applications.

All device outputs can sink and source 350 mAand 200 mA respectively. Prevention from crossconduction is ensured by interlocking anddeadtime function.

The device has dedicated input pins for eachoutput and a shutdown pin. The logic inputs areCMOS/TTL compatible down to 3.3 V for easyinterfacing with control devices. Matched delaysbetween low-side and high-side sectionsguarantee no cycle distortion and allow highfrequency operation.

The STDRIVE601 embeds a comparatorfeaturing advanced SmartSD function also integrated in the device, ensuring fast andeffective protection against fault events like overcurrent, overtemperature, etc.

Dedicated UVLO protection on the low-sides andeach of the high-side driving sections allow toprevent the power switches from operating in lowefficiency or dangerous conditions.

The integrated bootstrap diodes as well as all ofthe integrated features of this IC make theapplication PCB design easier, more compact andsimple thus reducing the overall bill of material.

The device is available in SO-28 package.

STDRIVE601主要特性:

 High voltage rail up to 600 V
 Driver current capability:
– STDRIVE601:
– 200 mA source current @ 25℃
– 350 mA sink current @ 25℃
 dV/dt transient immunity ±50 V/ns
 Gate driving voltage range from 9 V to 20 V
 Overall input-output propagation delay: 85 ns
 Matched propagation delay for all channels
 3.3 V, 5 V TTL/CMOS inputs with hysteresis
 Integrated bootstrap diodes
 Comparator for fast overcurrent protection
 Smart shutdown function
 Interlocking and deadtime function
 Dedicated Enable pin
 UVLO function on low-side and high-sides

STDRIVE601应用:

 3-phase motor drives
 Inverters

图1.STDRIVE601框图

图2. STDRIVE601典型应用框图

三相栅极驱动器演示板EVALSTDRIVE601

Demonstration board for STDRIVE601 triple gate driver
The EVALSTDRIVE601 demonstration board is a complete 3-phase inverter which allows evaluating all of the STDRIVE601 features. The power stage features STGD6M65DF2 IGBTs, but can be populated with any IGBT or power MOSFET in DPAK or powerFLAT 8x8 HV package. The board is designed to support a three shunt or a single shunt current sensing topology.

A strip connector allows an easy interfacing with MCU control.
The STDRIVE601 is a 600V gate driver device manufactured with BCD6s offline technology. It is a single-chip with three half-bridge gate drivers for N-channel power MOSFETs or IGBTs suitable for 3-phase applications.The device integrates three bootstrap diodes and a smart shutdown feature able to detect very fast overcurrent condition, minimizing the propagation delay between the overcurrent event and the output switch-off.

图3.演示板EVALSTDRIVE601外形图

演示板EVALSTDRIVE601主要特性:

• High voltage rail up to 600V
• Driver supply input voltage range 9V-20V
• STGD6M65DF2 IGBTs power stage featuring:
– V(BR)CES = 650 V
– VCE(sat) = 1.55 V @ IC = 6 A
• Dual footprint for IGBT/MOSFET package:
– DPAK
– PowerFlat 8x8
• Selectable single or 3-shunt current sensing topology:
– Sensored or sensorless BEMF detection
– FOC or 6-Step algorithm
• SmartShutdown overcurrent protection
• Hall effect sensors connector
• Bus voltage sensing
• 450V bulk capacitor
• Connector for interfacing with MCU
• RoHS compliant

演示板EVALSTDRIVE601应用:

• Three-phase motor drives
• Fans
• Pumps
• Refrigerator compressors
• Industrial inverters
• Appliances

图4.演示板EVALSTDRIVE601电路图(1):驱动器输出级

图5.演示板EVALSTDRIVE601电路图(2):反馈网络
演示板EVALSTDRIVE601材料清单:



图6.演示板EVALSTDRIVE601 PCB布局图(1):顶层元件布放

图7.演示板EVALSTDRIVE601 PCB布局图(2):顶层

图8.演示板EVALSTDRIVE601 PCB布局图(3):底层
详情请见:
https://www.st.com/content/ccc/resource/technical/document/datasheet/group3/9c/26/55/d5/fc/e0/43/cc
/DM00604820/files/DM00604820.pdf/jcr:content/translations/en.DM00604820.pdf

https://www.st.com/content/ccc/resource/technical/document/data_brief/group2/9c/72/e9/39/4c/92
/45/1a/DM00612114/files/DM00612114.pdf/jcr:content/translations/en.DM00612114.pdf

用户喜欢...

干货 | 齿轮传动噪声形成的主要原因及对策

selina 在 周一, 06/12/2017 - 08:58 提交 传统衡量齿轮传动性能的两个主要因素是:负载能力和疲劳寿命,往往将传动噪音与传动精度忽略掉。随着ISO14000、ISO18000两项标准的相继颁布,控制齿轮传...


细数工业领域内主要应用的电机

selina 在 周五, 06/09/2017 - 09:17 提交 工业领域内,中小型三相异步电机是目前应用最广泛的电机产品,不同的电机有不同的应用场合,随着电机制造技术的不断发展和对电机工作原理研究的不断...


三相变频电源采用FPGA数字化控制、瞬时波形控制及高频脉宽调制(SPWM)等技术

selina 在 周三, 03/22/2017 - 10:56 提交 众所周知,三相变频电源采用FPGA数字化控制、瞬时波形控制及高频脉宽调制(SPWM)等技术,用主动元件IGBT模块设计使单机容量最高达240KVA,以隔离变压器输...


永磁同步电机介绍

selina 在 周二, 12/20/2016 - 11:39 提交 目前我国电动机保有量大,消耗电能大,设备老化,效率较低,已完全进入更新换代的时期,而永磁同步电动机(PMSM)具有体积小、效率高、功率因数高、起动...


ADuM4121/ADuM4121-1评估板介绍

selina 在 周一, 01/09/2017 - 13:27 提交 领域 * 电机控制系统设计 * 仪器仪表和测量 * 能源 * 通信 * 汽车应用 * 航空航天和防务 特点 * 2 A峰值驱动输出能力 * 输出功率器件电阻:* 低传播延迟:* 工...


串行嵌入式计算的主要标准CompactPCI:提高工业系统设计安全

工业系统设计人员目前正在利用CompactPCI®串行结构以实现可以支持相关实时数据共享、分析和归档的各种系统。通过这些系统,工业性能向改善的灵活性、更好的产品质量和更少的工伤事故的方向而提高。...